Included in your Scorpion Package are the following whips. All have quick disconnect fittings so they can be interchanged quickly and easily. Heat Seal now offers the Reverse Octopus. This tool works just like out original Octopus Whip but pushes the debris back towards you. NOTE:   Higher air pressure is more productive and cleans easier.

SS-16		Octopus Predator Whip 14" long	Qty $64.00 or 3 for $159.00
		The best cleaning tool we make! Also available in low pressure designed for as low as 100 to 150 PSI working pressure. Uses 1/3rd less air than the Mini Predator. Cleans insulated duct and flex duct better than any other tool without damaging it. Makes metal ductwork shine in an instant. Is the fastest, most thorough duct cleaning tool ever made. Gets into corners - 14" long tentacles. Can be adapted to any rod system. Reusable - tentacles can be replaced. Compressed air causes the 8 tentacles to thrash in every direction at once hitting the duct work and wiping it clean. Can be used in every duct.
SS-16-28		Octopus Predator Whip – 28” long	Qty $74.00 or 3 for $183.00
SS-16LP		Octopus Predator Whip LP – 14” long	Qty $64.00 or 3 for $159.00
		Specifically designed for working under low pressure as low as 100 PSI
SS-16-28LP		Octopus Predator Whip LP – 28” long	Qty $74.00 or 3 for $183.00
		Specifically designed for working under low pressure as low as 100 PSI
SS-15		MINI Predator Whip	Qty $40 or 3 for $99.00
		3 headed whip that will go through a 1" hole. Does not hang up on wires or other obstructions. Can be used in every duct. 14" long tentacles. Reusable - tentacles can be replaced.
SS-8		ORIGINAL Predator Whip	Qty $40.00 or 3 for $99.00
		3 1/4" Ball which requires a 4" hole. Excels where you have to travel over 50' in the duct work. Also slides or travels better in flexible duct.
SS-3		SINGLE Predator Whip	Qty $11.00
		12" Whip with male QD Our most aggressive whip for loosening caked on debris
REPLACEMENT TENTACLES
SS-16-T		For Octopus Predator Whip -14" Long	Qty $20.00
		For Octopus Predator Whip with brass inserts. (8 per set)
SS-16-28-T		For Octopus Predator Whip - 28" Long	Qty $30.00
SS-16LP-T		For Octopus Predator Whip -14" Long	Qty $20.00
		For Octopus Predator Whip with brass inserts. Please not Octopus tentacles are now available for working under low pressure, as low as 100-150 PSI.
SS-16-28LP-T		For Octopus Predator Whip - 28" Long	Qty $30.00
		For Octopus Predator Whip with brass inserts. Please not Octopus tentacles are now available for working under low pressure, as low as 100-150 PSI.
SS-15-T		For Mini Predator Whip - 14" Long	Qty $ 5.00
		For Mini Predator Whip with brass inserts. (3 per set)
SS-15-TO		For Mini Predator Whip - Tubing Only - Sold by the foot	Qty $ 1.00
SS-8-T		For Original Predator Whip - 14" Long	Qty $ 5.00
		For Original Predator Whip. (3 per set)
SS-8-TO		For Original Predator Whip - Tubing Only - Sold by the foot	Qty $1.00
SS-3-T		For Single Predator Whip - tubing only	Qty $2.00
		For Single Predator Whip
SS-18-T		For Scorpion Brush (3 per set)	Qty $3.00

SCORPION PARTS Heat Seal's rods and snakes have longer lasting steel male QD. This makes the best rods in the business "Better than Ever". Lengthens the life of our rods greatly. Is available as a replacement part.
SS-1A		5' X 3/8" Blue Medium Flexible Rods	Qty $40.00
		These rods have a memory. They can be bent in a 90 degree angle and will stay that way. They are flexible enough to tie in an 8" diameter knot. With steel fitting.
SS-1B		5' X 3/8" White Stiff Rods	Qty $40.00
		When you bend the ends in a circle so they touch, the rods will spring back to being straight again (like a bow and arrow) With steel fitting.
SS-1C		5' X 1/4" White Stiff Rods	Qty $40.00
		When going straight up in a shaft, these rods support their own weight and remain straight. These rods are made of the same material as our stiff rods only 1/4" I.D. instead of 3/8". With steel fitting.
Users Comment: "These rods are very flexible."
SS-1D		5' X 5/8" O.D. White Stiff Rods	Qty $43.00
		Our stiffest rods ever made. Excellent for very long runs and great control.
Purchase any 10 rods and get the 11th one free!
SS-BV-1/4 SS-BV-3/8		Ball Valve with Scorpion Female QD This tool is used to connect the scorpion rods to the airline.	Qty SS-BV-1/4" fittings $21.00
			Qty SS-BV-3/8" fittings $23.00
SS-TV-1/4 SS-TV-3/8		Thumb Valve with Scorpion Female QD This tool is used to connect the Scorpion Rods to the air line. Allows you to give short bursts of air at maximum flow.	Qty SS-TV-1/4" fittings $28.50
			Qty SS-TV-3/8" fittings $30.50
SS-BV-H-1/4 SS-BV-H-3/8 SS-H-T		Ball Valve with 5' clear braided tubing and Scorpion Female QD This tool is used to connect the scorpion rods to the airline.	Qty SS-BV-H-1/4 1/4" fittings $28.50
			Qty SS-BV-H-3/8" fittings $30.50
			Qty SS-H-T Tubing with scorpion fitting only $20.00
SS-TV-H-1/4 SS-TV-H-3/8 SS-H-T		Thumb Valve with 5' clear braided tubing and Scorpion Female QD This tool is used to connect the Scorpion Rods to the air line. Allows you to give short bursts of air at maximum flow.	Qty SS-TV-H-1/4" fittings $36.00
			Qty SS-TV-H-3/8" fittings $38.00
			Qty SS-H-T Tubing Only with Female QD $20.00
SN-20		SNAKE - 20' Length (our most popular)	Qty $59.00
		Has scorpion quick disconnect on ends. Used for smaller ductwork such as cold air returns, supply vents and dryer vents. Made of 1/4" I.D. tubing which is the same plastic as our medium flexible rods (SS1A). Stiff enough to push forward blowing balls down the return but flexible enough to go around elbows. Can connect to the rods. Longer lengths available up to 100'. Add $5.25 for every extra 5 feet. With steel fitting.
SN-25		SNAKE - 25' Length	Qty $64.25
		With steel fitting.
SN-30		SNAKE - 30' Length	Qty $69.50
		With steel fitting.
SN-35		SNAKE - 35' Length	Qty $74.75
		With steel fitting.
SS-18		Scorpion Spinning Brush Improved design, more torque	Qty $60.00
		This new tool for the Scorpion System is used when super aggressive brushing is required. Works only in round duct 6" or less. Needs a minimum of 175 psi to operate blows in reverse. Bristles act like helicopter blades and help push debris back towards you. When whips will not clean, this is the tool to try. Replacement bristles available. Can only be used on Scorpion rods and snake.
SS-4		#4 Forward Blowing Skipper Ball for Scorpion	Qty 1 - 5 $27.00, 6 - 14 $23.00 or 15+ $20.00
		Used to loosen and push debris away from you, towards the suction hose. Comes with male scorpion QD (SS5).
SS-6		#6 Reverse Blowing Skipper Ball for Scorpion	Qty 1 - 5 $27.00, 6 - 14 $23.00 or 15+ $20.00
		Used to loosen and pull debris towards you and the suction hose. Comes with male scorpion QD (SS5).
SS-9		#3 Reverse Blowing Spinning Ball for Scorpion. Improved Spinning Power.	Qty $55.00
		Excels in small round ductwork especially in dryer vents. Used on the end of the 20' snake, this spinning skipper ball will pull the snake around elbows. Comes with male scorpion QD (SS14).
SS-10		#5 Forward Blowing Spinning Ball for Scorpion	Qty $55.00
		Excels in small round ductwork especially in dryer vents. Because the end is alive or moving around all the time it finds its way around elbows much easier than other tools. Comes with male scorpion QD (SS14).
SS-FB-4 SS-FB-3		Flexible Duct 4" Ball Goes between Scorpion rods and scorpion agitation device. Travels over flexible ductwork which does not catch on the ribs.	Qty SSFB 4" Ball $34.00
			Qty SS-FB-3 3" Ball $34.00

SS-2A		1/4" NPT Male Thread x Female QD (Replacement for SS2 and SS2T)	Qty $17.00
SS-5		1/8" NPT Male Thread x Male QD NPT thread fits non-spinning skipper balls.	Qty $ 9.00
SS-7		1/4" NPT Female Thread x Male QD Brass Fitting for Original Predator (SS8) and Flexible Duct Ball (SSFB)	Qty $ 9.00
SS-17		3/8" NPT Male Thread x Male QD Brass Fitting for Octopus Predator (SS16) and Mini Predator (SS15)	Qty $ 9.00
		REPLACEMENT FITTINGS FOR 3/8" SCORPION RODS
SS-11		3/8" Hose Barb x Female QD	Qty $18.75
SS-12		3/8" Hose Barb x Male QD	Qty $10.00
		Improved steel fitting
		REPLACEMENT FITTINGS FOR 1/4" RODS & SNAKE
SS-13		1/4" Hose Barb x Female QD	Qty $18.75
SS-14		1/4" Hose Barb x Male QD Improved steel fitting	Qty $10.00

CARE AND MAINTENANCE OF SCORPION RODS Cleaning Female Quick Disconnects Dip fittings in mineral oil (varsol or paint thinner) and give them a blast of air from a blowgun which cleans the liquid and the dust out of them. Do this several times to get them really clean. Do not use any solvent that contains oil. Do not lubricate with oil as the film will only attract and hold on to the dirt, where as dry fittings stay cleaner longer. Trouble Shooting If you are not able to connect the rods, the female quick disconnect may be in the locked position, (will not accept the male plug).(Fig. 1) Take a pencil and depress the plunger inside the fitting about 1/4" and hold it there. (Fig. 2) Then grab the outer sleeve and pull it back and hold there, (Fig. 3) then release the pencil. (Fig. 4) The outer sleeve should stay back which means the quick disconnect is unlocked ready to use. (Fig. 5) Another way of telling whether the quick disconnect is locked is to compare the outer sleeve on an unlocked fitting. (Fig. 6) The outer sleeve on a locked fitting is more forward than the other fitting. Storage To keep rods straight in the truck, use 4' of PVC tubing and install at a 45 degree angle on the wall of your truck.

Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Locked Unlocked